The official website of Kodera Electronics Co.,Ltd.
We've achieved a wide range of machining of AWG#2(30sq)～AWG#28(0.08sq) in one machine.
It can be widely used in a wide variety of industries since it corresponds to the round cable up toφ11mm maximum diameter.
| MODEL | C373A | |
|---|---|---|
| OUTER DIMENSIONS | W430mm ×D510mm ×H265mm | |
| WEIGHT | 33kg | |
| POWER SUPPLY | AC100V or AC200V~240V(Single Phase)50Hz/60Hz | |
| POWER CONSUMPTION（100V） | 40W（Rated）215W（Max） | |
| AIR SUPPLY | 9Nℓ/min 0.5MPa※1 | |
| CUTTING LENGTH | 0.1mm～99,999mm | |
| CUTTING TOLERANCES | ±（ 0.1＋0.0005×L ）mm※2 L : indicates a cutting length. | |
| STRIPPING LENGTH | FRONT END | 0.1～47.9mm |
| REAR END | 0.1～47.9mm | |
| APPLICABLE WIRES | TYPE | AVSS,VSF, IV, KV, UL,Teflon , Glass Wire, etc |
| SIZE | AWG#2(30sq）～AWG#28（0.08sq）※2 | |
| O.D. | Max φ11mm※2 | |
| WIRE FEED SPEED | Variable | |
| CUTTER MATERIAL | Ultra fine particle alloy | |
| DRIVE SUPPLY | Stepping pulse motor / Air cylinder | |
※1. Use clean,dry air. ※2. Depending on the wire type.
| Total Length | Pieces |
|---|---|
| 100mm | 2,300 |
| 200mm | 2,100 |
| 300mm | 1,950 |
| 500mm | 1,700 |
| 800mm | 1,450 |
| 1000mm | 1,300 |
| 1500mm | 1,050 |
| 2000mm | 850 |
| 3000mm | 650 |
| 5000mm | 450 |
Core diameter : 0.75mm
Blade move back : 0.15mm
Both ends stripping : 3mm
Setting of speed : 9
Normal mode
Wire : UL1007／AWG#22
Automatic mid stripping is realized.
CMS-801A2 can handle wires with an outer diameter of up to 8mm.
It can mid strip in up to 10 different positions on a single wire.
Automation has been accomplished thus far by this revolutionary equipment.
| MODEL | CMS-801A2 |
|---|---|
| OUTER DIMENSIONS | W185mm ×D355mm ×H190mm |
| WEIGHT | 12kg |
| POWER CONSUMPTION | MAX390W 65W while idling※ |
| MID STRIPPING LENGTH | Max. up to 34mm |
| MID STRIPPING DISTANCE | Min. 48.5mm |
| MID STRIPPING POSITIONS | Max. up to 10positions |
| MAX WIRE SIZE | φ8mm |
| DRIVE | Stepping motor |
Just set up CC-100 on the left side of the CASTING series, it carries the finished wires by belt-conveyor and neatly deposits those wires on the tray.
It contributes to improving the work efficiency rate.
| MODEL | CC-100 |
|---|---|
| OUTER DIMENSIONS | W1200mm ×D340mm ×H135mm |
| WEIGHT（NET） | 10kg |
| POWER SUPPLY | AC100VorAC200V（single phase）50Hz/60Hz |
| POWER CONSUMPTION | MAX15W（AC100V） |
| O.D. SIZE | φ1mm Minimum※ |
| DRIVE | Induction motor |
| Air cylinder |
※Depends on wire type